Igo, that was talking about, dude, look this one
that's not one case of issue, can you see?
but.. we can see..
it's.. wet inside, are you look?
but this one doesn't came to us with oxidation's issue
probably will, right?
This lamp has a little.. it's wet inside, can you see?
like if the vedation didn't work..
right, like had entered some.. water
[for camera-man] can see a few water inside by video?
[for camera-man] can see, right?
[camera-man] yes, it can
probably this is from the last request, it's a new one (3 months ago), so..
you see already marks of water inside, are you look?
here, look
have a little vapor of water inside
but it's not oxidized yet, but probably
will, right? has some marks of water here..
I don't know if it's oxidation or was provoque by soldering iron
it's...
I think that inside is begining a litte mark, but very lightly
But probably this lamp here should have 3 months of use
The problem is when past some time and it will..
We're found more issues with lamps with more than 8 months of use but..
this few water that it's inside certainly will oxidize!
about the clamping I was talking about this is it, look
when we..
press here to seal, you give a maximum clamped, right
done, here I think the lamp is sealed
but sometimes, the lock didn't match with this..
this slot...
For example, here, look
I pressed a little more, you looking?
so..
here it's in.. in maximum
I also don't know if so much tightening is needed
but certainly the vedation depends entirely on that tightness
what I would like do is: I would do.. or.. right.. here, look
I'm pressing more
done, I pressed a lot
but when I openned it, it didn't was with on that maximum tightness
I think was 3 levels down
that we can see even by.. by the mark
I will to open other over there for we see it
But I'm realize this: sometimes the lamps is not at..
at maximum
And this one.. really.. this one now doesn't tight more..
So, I don't know if it would be Brando's recomendation have all this tightness
to vedation really works good, because
this rubber here
right? depends entirely on that.. only will seal if have this tightness
if not, will not work indeed
Will have water inside, no doubt
I'll get other lamp, let me see here
look, I'll do..
this one we improvised one.. one screwdrive here
philips.. triangule, right?
[camera-man] mickey's screwdrive
mickey's screwdrive
here, look..
I had unlock it, right? Look how much tightness still left...
did you see how much I turn?
you got it?
so, this one.. it was untouched, new
did you see how much tightnes I gave it yet? still got it
so, perhaps this question about tightness is the main issue
I need to know if Brand recommend or not
how much tightness untill maximum point
look, this one not was openned before
I just press it here, look..
look
so, the lock is not been working good in this case
look
it's a case that show that lock is not much efficient
here, look
if it allows this turn..
this on has watermark and dust inside, you looking?
[to camera-man] can see that?
[camera-man] yes
water and dust
here has on side too, look
it's entering
it's really..
the ideal is..
we should have tight it
and the lock works, but..
you see this lock is so high that it goes as far as it shouldn't, so it gives..
allows us.. Look, all this movement here
I took a new one
[to camera-man] with no.. with no.. oh ok, I thought it was no flashlight (the camera)
I took a new one for we've take a look
the locks is not worn like the other one
but you can see that has, look
the bezel moves, right?
the lock here it's really
works
allows this, this.. a little movement here but doesn't do what the other lamp did
I don't know if this with detrition, the people using it will be
wasting and allowing the bezel turn it
but I'll make the followed test: I'll open this new one, never was openned
and se if it really need more tightness
[to camera-man] pause, please
I'll loosen here for our test, right?
really, still.. still has a bit of tightness
almost one more, more one step, right?
so, this is a new lamp, right?
I hadn't touched this lamp before
right, there is this issue here
the issue is: it's need much more tightness for rubber work properly
maybe if the rubber was..
more..
hm.. soft..
maybe we would get much more vedation, a better one
but is entering dust and water
I don't know if
with time the lamp will been.. crashing with floor..
the lamp goes..
the rubber will can be works not so good
but the issue is:
the lamp was tight in this step.. this step here
so, I'm tight more here
the bezel is going to the next step
it's the maximum of strength I can do